perezoso
About
- Username
- perezoso
- Joined
- Visits
- 31
- Last Active
- Roles
- Member
- Points
- 1
Comments
-
TLDR: AI-64 differences? One of my v1s has the cycling problem after I did a 701 to 808 update. The other updated just fine. (I am only at the Kiwi site about half the year and don't perform updates when gone.) I'm happy to fix this myself, howev…
-
These have been whirring away for me for more than a year: https://www.amazon.com/gp/product/B00G05A2MU/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 With a box of the spacers below, and some of the rubber feet from the fan, you can make "…
-
On the power question: Although I'm no RFI expert, since there's a big 13.8v ham shack linear power supply close to my Kiwis, rather than the spendy 5v linear (which get hot in my experience), I now just feed shack power to a step down transformer t…
-
What type and location of account are we ultimately paying into? A US bank account, a Kiwi account or something else? I suppose I'm in the minority, but I loathe Paypal and its owners and it taking a cut on so many transactions where it really isn'…
-
Firm order for one, probably two, and maybe three, depending on price point. If it matters, my orders are likely board only as I'd probably pair them with AI-64s.
-
Or the barrel connector on the BBAI-64, in my case, which works fine, and can be fed enough potential amps that I don't sweat underpowering anything. This is great news. I have toyed with many SDRs and will continue to experiment with others, but t…
-
Unfortunately I no longer have the output of the make. Dog says: Debian 11.7 BeagleBoard.org Debian Bullseye Xfce Image 2022-01-14 Linux BeagleBone 5.10.168-ti-arm64-r103 #1bullseye SMP Fri May 12 23:47:21 UTC 2023 aarch64 GNU/Linux Debian GNU/Linux…
-
That resulted in an unexpectedly short "make" command (just a few minutes). "Make install" then completed without error. But unfortunately, although halting the AI64 and rebooting seemed normal, when I removed power, attached t…
-
Err. Groan. Looks like the third time was unlucky. Everything was going fine, but "make install" exited with "Error 2". So I'm looking at this (accidentally hit control-c after the error trying to copy, so disregard that): ht…
-
Okay, I was just about to do a third AI-64. I take it from the above discussion that I'm safe provided that I don't set the enet speed to 10 mbps and follow the directions at the start of the thread? (Which I've done successfully twice.) Oh, what …
-
Operation successfully performed on a second AI-64 (which are back in stock widely, and the brief price spike has subsided). One small hiccup. The "git pull -v" command resulted in a error, see image below. I exhaled and tried it again, …
-
My goal is to be off-grid on the back 40 here. I run the K3WRG beacon, which is essentially untouched for a year now, and is solar powered. But it is very close to my receive setup, so I'm deaf on the default WSPR transmit cycle, and it causes issue…
-
What I observe with a cheap clamp-type meter is: 1.7A running solo 2.2-2.3A running with the Bodnar and fan attached to USB ports 2.7A maximum registered on startup
-
I did not give myself particularly good odds performing this operation, but after carefully following the directions ... SUCCESS! Your mileage may vary, but for any other history majors sitting on the fence about this one, I can at least say that i…
-
I'm hoping you are successful with this effort. I have three Kiwis, but have shied away from the BBAI because it looked to me as if it may be more trouble than it's worth, at least to this CLI-phobic guy. But it sure would be nice to have the addi…
-
Ordered from ML&S Friday the 10th, received in good shape on the US East Coast on Thursday the 16th. No problems.
-
Ordered a Kiwi from ML&S (UK) for shipping to North America on Friday night (US time), cost was a reasonable US $296, including shipping. Will update this post on service from ML&S. Enclosure from Mouser.
-
Hi Folks - I've had Kiwi for just a few days but already love it. A second is on the way to use as an 8 channel WSPR receiver. A question about wsprdaemon: I'd like to use an Ubuntu-friendly SBC like Odroid as the wsprdaemon host machine. I us…
-
I am glad to hear there are more coming. I ordered one from Amazon (US) on June 7th and got an email on the 10th that the order was cancelled because it was actually out of stock. Looks like a fun radio to complement the ELAD.