bbachmann
About
- Username
- bbachmann
- Joined
- Visits
- 335
- Last Active
- Roles
- Member
- Points
- 5
Comments
-
Thank you John Mine has arrived today - order #1164 It is working and it has GPS fix with 10 sat's within 2 minutes 😀 Best Regards Bjarne - OZ1AEF
-
I have also seen short audio drops 1-1.5sec on my KiwiSDR (http://85.191.35.22:8073). But only when all 4 users are active. My KiwiSDR is standing in +23.
-
I'll take 1
-
I think I have found it :-)
-
:-) You are allowed to play with my system, write a note, if you need SSH access Thanks for info
-
http://forum.kiwisdr.com/index.php?p=/discussion/comment/12844#Comment_12844 Hi John You may use my Kiwisdr oz1aef.ampr.org (http://85.191.35.166:8073). it is located in Denmark. Look at it and see if it it useable for you, and I will give you SSH a…
-
I have a Raspberry 3B up running with RTL-SDR v2 and a wideband disc cone antenna. It is registered as 'Bjertrup_Denmark'. Working, yes. But what it can be used to, is another question... Regards Bjarne - OZ1AEF
-
looks interesting, will try to install on a raspberry 3B when I arrive home again
-
Hi GNURadio v. 3.7.13.4 boost-1.66.0_3 I will inform you if I find any problems Regards Bjarne
-
Hi Christoph My gr-kiwisdr where updated yesterday. I have not made any updates today. On my computer I am running (OSX 10.14.2) Running the command 'volk_profile -R volk_16u_byteswap' solved the problem now is gr-kiwisdr running (What does that com…
-
Hi Christoph I run the 't2_kiwi.grc' It Returns the error: gr::log :DEBUG: kiwisdr0 - kiwisdr_impl::start >>> Done (return code -11) and in my KiwiSDR it logs: Sun Feb 3 17:54:50 09:34:51.289 ... [00] PWD isLocal_if_ip: flg=0x18 fam=2 s…
-
Hi, Christoph. I have installed the gr-kiwisdr. The installation was not a large problem on my iMac. The .grc files load fine and the graphics have no missing parts. But when i run the programs it stops after 2 to 3 sec with a runtime error. Any ide…
-
Hi John. How many CPU Cores do you have in linode3535501? Or is it time to find a sponsor in Europe with a 24 - 32 core node in a datacenter :-) /oz1aef
-
sounds interesting :-)
-
Mauritz: Are you thinking of EGNOS / WAAS DGPS or DGPS based on 300 kHz beacons?Regards Bjarne / OZ1AEF
-
Sounds great :-)Looking forward to test the new code BjarneOZ1AEF
-
Hi JohnMy antenna is located at a too low altitude to see the QZSS satellites. I need at least 25 meter more to look that low.It must also be an antenna with a large opening.
-
Hi John.I can see that you are working with til Galileo satellites. Are they useable in your part of the world, or du you need receivers in Europe?RegardsBjarne Bachmann
-
Hi, I am looking at ionosondes, look interesting, but I can not if it should be possible to make the KiwiSDR do a GPS-time controlled sweep.
-
Hi JohnAccording EFR (Teleswitch signals) You have 7N0V as framing.When I look in the papers it should be 8bit data + parity + 1 stop bit RegardsBjarne Bachmann
-
Hi I have tried the DX mode on 518 KHz18 Jan 2018 21:31:22 UTC | ZCZC JB03 | 171730 UTC JAN QI VARNA RADIO GALE AND SEA WARNING SYNOPTIC SITUATION AT ... 18 Jan 2018 21:32:22 UTC | ZCZC JB02 | 161800 UTC JAN 18 VARNA RADIO ON BEHALF OF ROMA…
-
Hi Remember that the Ubiquiti Bullet M5 have a buildin switchmode psu :-) /Bjarne
-
Are you shure that nobody else using the same IP-address and that the broadcast address is set correctly? Regards Bjarne
-
Looks fine, are they EMC tested? Thinking about shielding the VHF (145MHz) spurs Regards OZ1AEF Bjarne
-
Hi John,I have kiwifax.py up running and wondering if it possible to use the same method to transfer IQ signal to remote computer and decode with DREAM/DRM. RegardsBjarne Bachmann - OZ1AEF
-
Just what I am waiting for. Regards OZ1AEF Bjarne Bachmann