Powernumpty
About
- Username
- Powernumpty
- Joined
- Visits
- 5,458
- Last Active
- Roles
- Member
- Points
- 29
Comments
-
That field does not wrap over to "G" and seems to go negative. You'll find out these things when you have been running an AI as long as I have ;-) (joke)
-
Is this week a rollover? (Image)
-
Martin, let me know what base install you are using and I'll try the process again from a bare card. Not sure if you saw my last email with the steps from the SDRplay PI Image (only becasue I already had one running). I didn't see any problem gett…
-
For the record, on that screenshot I had slowed the waterfall to be able to make an image and it was a BBG. I have occasionally seen a very slow response after a change of zoom on the waterfall but that has normally been after the browser has been o…
-
I can't see it but then I'm running Hz here ;-p I did wonder if the waterfall changes to virtually black (where background noise is less) so there no visible movement? to test I zoomed to 14, adjusted the waterfall for visible noise, scrolled out.…
-
I took this off forum to see if I could help but probably didn't.... I can see (assume) the error is a permissions thing, like the logged on, daemon running user does not have permission to write to the wsprdaemon directory? The config file looks O…
-
Hi Martin, 192.168.0.52/24 is not the same range as your router 192.168.1.254/24 one or other is wrong. Regards Stu
-
Running the PI image here now, very good to play with. I'm not entirely sure how we are meant to stop and start the service and or connectors so have been doing a few reboots after changing things. It (the browser session) automatically tries to rec…
-
Hi Martin, might be wrong here but doesn't it cycle the leds while writing to the onboard memory? it can take a very long time, like walk away for 40minutes then come back see if it is dark. With no leds showing take the card out and power cycle it.…
-
Ha was just running the main version with an RTL dongle thinking "it's a shame this has not been worked on more" (filter widths, connection defaults, spectrum, etc.) Yes I know I should learn to code rather than criticise but I'm a wage sl…
-
I still want to have a go at reversing the stack, seems illogical to have the most thermally active sources in the least thermally accessible locations. If only they sold BeagleBones and Capes without soldered headers.
-
BBB? BeagleBone Blue or Black? Any other network interfaces?
-
In the notes it recommends "mv ~/wsprdaemon ~/wsprdaemon.save" Should not be something like "mv ~/wsprdaemon/wsprdaemon.conf ~/wsprdaemon.save" On my non standard VM I tried a couple of unsucessfull git pulls and obviously got i…
-
I've not seen anything but I'm not on the usual databases like QRZ so it would take a few minutes more to find an email address. Cheers Stu
-
One thing I have experienced is cached web pages, are you refreshing the admin pages before making changes?
-
Yes sorry if my reply was not very clear. I can see the slow down even with only two connections with LMS and Notch, I was not disagreeing with anyone. I can barely think and type at the same time (look up the meaning of numpty then add a turbo and…
-
OK so tested here two connections, LMS and Notch enabled, waterfall does slow quite a bit, don't have an old version to compare. Only "kiwid" seems to be taxing the CPU but hard to say if actual load much different on/off (from "top&q…
-
If you did make a database one thing I'd really like is the ability to run two or more systems and break down which works better on a band. I have one KiwiAI on a LZ1AQ loop (14Ch) and a second KiwiBBG on a Wellbrook (running 7 so I have a slot free…
-
Change something else like Initial Mode (just call up the drop down menu and back to the exisiting value). That forces a "restart required" and saves the change (it seems). Fudge but allows testing. Stu
-
Do a comparison of the working/not-working WSD configs? (using WinMerge, Beyond Compare etc. to avoid characters that "look OK") Just in case something about the ident or other lines affecting graph upload have a typo? I didn't see my gr…
-
It works from outside, I just tried it. From inside the network it may not work from http://w7pua.ddns.net:8073 as the router is stopping you looping back into the public interface from the private. Fair bit of noise on the antenna at the moment b…
-
Long shot, renew the admin connection (Ctrl +F5 to refresh or close and reopen the browser). On the GPS tab try these settings then see what it is doing. (Image) It might be that it was doing the full update so paused but the page has not properl…
-
Showing in the daily WSPR results now, excellent! I did have a look when you first posted but as it was a quiet part of the RF day and I could not recall the previous spectrum it was hard to comment. WSPR results are great for feedback on antennas …
-
OK bit difficult to say (guess) how that could happen without knowing where the VPN is in the path. Is it a static-IP vpn, not one that could change public endpoint?
-
Wasn't that related to some distant user who was tying up the connections with broken code? (the reason JKS gave the admin capability to block IP's). I'd look at the connections, see if any look ripe for blocking and block the most likely range. So…
-
Upvoted for the fun side, the world has got very serious, like we are all to blame for something and should feel bad all the time. I've just spent the last few minutes pointlessly staring at time signals like a cat watching birds, it was great.
-
That's probably how I'd have done it, there are few other ways but balance? Nah.
-
As well as wifi, remote links, neighbours cat. (I'm most sorry about the cat, it caught me at a low point).
-
Found my old phone. The Flir One uses a visual camera to add detail, obvious drawback is parallax, makes it next to useless close up. First is the AI with fan (mainly) on the heat pipe fins, second is what's on top of the case and why I don't open…
-
https://www.tp-link.com/uk/support/faq/1682 (Image) It is possible...