Nov  7 19:26:09 beaglebone rsyslogd:  [origin software="rsyslogd" swVersion="8.1901.0" x-pid="569" x-info="https://www.rsyslog.com"] rsyslogd was HUPed
Nov  7 19:26:16 beaglebone kernel: [   35.201740] remoteproc remoteproc0: wkup_m3 is available
Nov  7 19:26:16 beaglebone kernel: [   35.258759] remoteproc remoteproc0: powering up wkup_m3
Nov  7 19:26:16 beaglebone kernel: [   35.258787] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168
Nov  7 19:26:16 beaglebone kernel: [   35.259042] remoteproc remoteproc0: remote processor wkup_m3 is now up
Nov  7 19:26:16 beaglebone kernel: [   35.259067] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193
Nov  7 19:26:16 beaglebone kernel: [   35.413301] PM: bootloader does not support rtc-only!
Nov  7 19:26:18 beaglebone kernel: [   36.579943] remoteproc remoteproc1: 4a334000.pru is available
Nov  7 19:26:18 beaglebone kernel: [   36.580156] pru-rproc 4a334000.pru: PRU rproc node pru@4a334000 probed successfully
Nov  7 19:26:18 beaglebone kernel: [   36.582266] remoteproc remoteproc2: 4a338000.pru is available
Nov  7 19:26:18 beaglebone kernel: [   36.582440] pru-rproc 4a338000.pru: PRU rproc node pru@4a338000 probed successfully
Nov  7 19:26:31 beaglebone kiwid: 00:00:31.027   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens
Nov  7 19:26:31 beaglebone kiwid: 00:00:31.033   reading configuration from file /root/kiwi.config/admin.json: 119 tokens
Nov  7 19:26:31 beaglebone kiwid: 00:00:31.422   serial number from EEPROM: 1697
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.479   reading configuration from file /root/kiwi.config/dx.json: 7172 tokens
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.481   898 dx entries
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.495 ....      firmware: SDR_RX4_WF4
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.497 ....      firmware: rx_chans=4 wf_chans=4
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.499 ....      firmware: RX bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.501 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.502 ....      listening on default port 8073/8073 for "openwebrx"
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.507 ....      webserver for "openwebrx" on port [::]:8073
Nov  7 19:26:32 beaglebone kiwid: 00:00:31.757 ....      ### using SPI_DEV /dev/spidev0.0
Nov  7 19:26:33 beaglebone kiwid: 00:00:32.589 ....      FPGA version 1
Nov  7 19:26:33 beaglebone kiwid: 00:00:33.074 ....      using DC_offsets: I -0.020000 Q -0.020000
Nov  7 19:26:33 beaglebone kiwid: 00:00:33.449 ....      PROXY: NO dom_sel_menu=0
Nov  7 19:26:34 beaglebone kiwid: 00:00:33.545 ....      ip_blacklist_add_iptables: "iptables -A KIWI -s 47.88.219.24/24 -j DROP" rv=0
Nov  7 19:26:35 beaglebone kiwid: 00:00:34.816 ....      UPDATE: check scheduled (startup)
Nov  7 19:26:35 beaglebone kiwid: 00:00:34.820 ....      UPDATE: checking for updates
Nov  7 19:26:36 beaglebone kiwid: 00:00:35.619 ....      NET(0): private IPv4 <192.168.117.51> 0xc0a87533 /24 0xffffff00 eth0
Nov  7 19:26:36 beaglebone kiwid: 00:00:35.622 ....      NET(0): private IPv6 LINK-LOCAL <fe80::9a84:e3ff:fe92:e577%eth0> /64 ff:ff:ff:ff:ff:ff:ff:ff:00:00:00:00:00:00:00:00: eth0
Nov  7 19:26:36 beaglebone kiwid: 00:00:35.624 ....      auto NAT is set false
Nov  7 19:26:38 beaglebone kiwid: 00:00:38.453 ....      TIMEZONE: no lat/lon available from admin public config, ipinfo or GPS
Nov  7 19:26:38 beaglebone kiwid: 00:00:38.457 ....      TIMEZONE: will retry..
Nov  7 19:26:39 beaglebone kiwid: 00:00:39.027 ....      IPINFO: public ip 145.224.99.183 from extreme-ip-lookup.com
Nov  7 19:26:45 beaglebone kiwid: 00:00:44.874 ....      MY_KIWI: registered
Nov  7 19:26:53 beaglebone kiwid: 00:00:53.380 0... 0        0.00 kHz  am z0  "SNR-measure" 127.0.0.1 internal task (ARRIVED)
Nov  7 19:26:55 beaglebone kiwid: 00:00:54.899 .... 0        0.00 kHz  am z0  "SNR-measure" 127.0.0.1 internal task (LEAVING after 0:00:01)
Nov  7 19:27:38 beaglebone kiwid: 00:01:38.459 ....      TIMEZONE: no lat/lon available from admin public config, ipinfo or GPS
Nov  7 19:27:38 beaglebone kiwid: 00:01:38.475 ....      TIMEZONE: will retry..
Nov  7 19:28:38 beaglebone kiwid: 00:02:38.484 ....      TIMEZONE: no lat/lon available from admin public config, ipinfo or GPS
Nov  7 19:28:38 beaglebone kiwid: 00:02:38.489 ....      TIMEZONE: will retry..
Nov  7 19:28:43 beaglebone kiwid: 00:02:43.602 ....      UPDATE: version changed, current 1.486, new 1.633
Nov  7 19:28:43 beaglebone kiwid: 00:02:43.607 ....      UPDATE: building new version..
Nov  7 20:23:09 beaglebone rsyslogd: imuxsock: Acquired UNIX socket '/run/systemd/journal/syslog' (fd 3) from systemd.  [v8.1901.0]
Nov  7 20:23:09 beaglebone rsyslogd:  [origin software="rsyslogd" swVersion="8.1901.0" x-pid="550" x-info="https://www.rsyslog.com"] start
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Booting Linux on physical CPU 0x0
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Linux version 4.19.94-ti-r42 (voodoo@x3-am57xx-beagle-x15-2gb) (gcc version 8.3.0 (Debian 8.3.0-6)) #1buster SMP PREEMPT Tue Mar 31 19:38:29 UTC 2020
Nov  7 20:23:09 beaglebone kernel: [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
Nov  7 20:23:09 beaglebone kernel: [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Nov  7 20:23:09 beaglebone kernel: [    0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Green
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Memory policy: Data cache writeback
Nov  7 20:23:09 beaglebone kernel: [    0.000000] cma: Reserved 48 MiB at 0x9c800000
Nov  7 20:23:09 beaglebone kernel: [    0.000000] CPU: All CPU(s) started in SVC mode.
Nov  7 20:23:09 beaglebone kernel: [    0.000000] AM335X ES2.1 (sgx neon)
Nov  7 20:23:09 beaglebone kernel: [    0.000000] random: get_random_bytes called from start_kernel+0xac/0x4b4 with crng_init=0
Nov  7 20:23:09 beaglebone kernel: [    0.000000] percpu: Embedded 17 pages/cpu s38988 r8192 d22452 u69632
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129412
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Kernel command line: console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=UUID=758cef0a-29df-4f74-8831-183531e5e544 ro rootfstype=ext4 rootwait uboot_detected_capes=KIWISDR10 , coherent_pool=1M net.ifnames=0 lpj=1990656 rng_core.default_quality=100 quiet
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Memory: 437972K/522240K available (13312K kernel code, 1136K rwdata, 4308K rodata, 1024K init, 350K bss, 35116K reserved, 49152K cma-reserved, 0K highmem)
Nov  7 20:23:09 beaglebone kernel: [    0.000000] Virtual kernel memory layout:
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     vmalloc : 0xe0000000 - 0xff800000   ( 504 MB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     lowmem  : 0xc0000000 - 0xdfe00000   ( 510 MB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (14304 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   (1137 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 351 kB)
Nov  7 20:23:09 beaglebone kernel: [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Nov  7 20:23:09 beaglebone kernel: [    0.000000] ftrace: allocating 42043 entries in 124 pages
Nov  7 20:23:09 beaglebone kernel: [    0.000000] rcu: Preemptible hierarchical RCU implementation.
Nov  7 20:23:09 beaglebone kernel: [    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
Nov  7 20:23:09 beaglebone kernel: [    0.000000] 	Tasks RCU enabled.
Nov  7 20:23:09 beaglebone kernel: [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
Nov  7 20:23:09 beaglebone kernel: [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
Nov  7 20:23:09 beaglebone kernel: [    0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts
Nov  7 20:23:09 beaglebone kernel: [    0.000000] OMAP clockevent source: timer2 at 24000000 Hz
Nov  7 20:23:09 beaglebone kernel: [    0.000025] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
Nov  7 20:23:09 beaglebone kernel: [    0.000046] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
Nov  7 20:23:09 beaglebone kernel: [    0.000056] OMAP clocksource: timer1 at 24000000 Hz
Nov  7 20:23:09 beaglebone kernel: [    0.002472] Console: colour dummy device 80x30
Nov  7 20:23:09 beaglebone kernel: [    0.002501] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
Nov  7 20:23:09 beaglebone kernel: [    0.002506] This ensures that you still see kernel messages. Please
Nov  7 20:23:09 beaglebone kernel: [    0.002510] update your kernel commandline.
Nov  7 20:23:09 beaglebone kernel: [    0.002571] Calibrating delay loop (skipped) preset value.. 995.32 BogoMIPS (lpj=1990656)
Nov  7 20:23:09 beaglebone kernel: [    0.002586] pid_max: default: 32768 minimum: 301
Nov  7 20:23:09 beaglebone kernel: [    0.002872] Security Framework initialized
Nov  7 20:23:09 beaglebone kernel: [    0.002887] Yama: becoming mindful.
Nov  7 20:23:09 beaglebone kernel: [    0.003033] AppArmor: AppArmor initialized
Nov  7 20:23:09 beaglebone kernel: [    0.003138] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.003150] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.004243] CPU: Testing write buffer coherency: ok
Nov  7 20:23:09 beaglebone kernel: [    0.004307] CPU0: Spectre v2: using BPIALL workaround
Nov  7 20:23:09 beaglebone kernel: [    0.004790] CPU0: thread -1, cpu 0, socket -1, mpidr 0
Nov  7 20:23:09 beaglebone kernel: [    0.025195] Setting up static identity map for 0x80100000 - 0x80100060
Nov  7 20:23:09 beaglebone kernel: [    0.033100] rcu: Hierarchical SRCU implementation.
Nov  7 20:23:09 beaglebone kernel: [    0.049114] smp: Bringing up secondary CPUs ...
Nov  7 20:23:09 beaglebone kernel: [    0.049134] smp: Brought up 1 node, 1 CPU
Nov  7 20:23:09 beaglebone kernel: [    0.049145] SMP: Total of 1 processors activated (995.32 BogoMIPS).
Nov  7 20:23:09 beaglebone kernel: [    0.049151] CPU: All CPU(s) started in SVC mode.
Nov  7 20:23:09 beaglebone kernel: [    0.050880] devtmpfs: initialized
Nov  7 20:23:09 beaglebone kernel: [    0.085523] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
Nov  7 20:23:09 beaglebone kernel: [    0.086151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
Nov  7 20:23:09 beaglebone kernel: [    0.086176] futex hash table entries: 256 (order: 2, 16384 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.090165] xor: automatically using best checksumming function   neon      
Nov  7 20:23:09 beaglebone kernel: [    0.090182] pinctrl core: initialized pinctrl subsystem
Nov  7 20:23:09 beaglebone kernel: [    0.091506] NET: Registered protocol family 16
Nov  7 20:23:09 beaglebone kernel: [    0.096642] DMA: preallocated 1024 KiB pool for atomic coherent allocations
Nov  7 20:23:09 beaglebone kernel: [    0.231407] audit: initializing netlink subsys (disabled)
Nov  7 20:23:09 beaglebone kernel: [    0.237198] audit: type=2000 audit(0.224:1): state=initialized audit_enabled=0 res=1
Nov  7 20:23:09 beaglebone kernel: [    0.240392] OMAP GPIO hardware version 0.1
Nov  7 20:23:09 beaglebone kernel: [    0.267158] hw-breakpoint: debug architecture 0x4 unsupported.
Nov  7 20:23:09 beaglebone kernel: [    0.293257] raid6: using algorithm neonx8 gen() 0 MB/s
Nov  7 20:23:09 beaglebone kernel: [    0.293270] raid6: .... xor() 0 MB/s, rmw enabled
Nov  7 20:23:09 beaglebone kernel: [    0.293277] raid6: using neon recovery algorithm
Nov  7 20:23:09 beaglebone kernel: [    0.301567] edma 49000000.edma: TI EDMA DMA engine driver
Nov  7 20:23:09 beaglebone kernel: [    0.308687] SCSI subsystem initialized
Nov  7 20:23:09 beaglebone kernel: [    0.313520] usbcore: registered new interface driver usbfs
Nov  7 20:23:09 beaglebone kernel: [    0.313591] usbcore: registered new interface driver hub
Nov  7 20:23:09 beaglebone kernel: [    0.313711] usbcore: registered new device driver usb
Nov  7 20:23:09 beaglebone kernel: [    0.315826] omap_i2c 4802a000.i2c: bus 1 rev0.11 at 100 kHz
Nov  7 20:23:09 beaglebone kernel: [    0.317458] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz
Nov  7 20:23:09 beaglebone kernel: [    0.318096] pps_core: LinuxPPS API ver. 1 registered
Nov  7 20:23:09 beaglebone kernel: [    0.318106] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
Nov  7 20:23:09 beaglebone kernel: [    0.318128] PTP clock support registered
Nov  7 20:23:09 beaglebone kernel: [    0.319076] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
Nov  7 20:23:09 beaglebone kernel: [    0.321544] Advanced Linux Sound Architecture Driver Initialized.
Nov  7 20:23:09 beaglebone kernel: [    0.322390] NetLabel: Initializing
Nov  7 20:23:09 beaglebone kernel: [    0.322399] NetLabel:  domain hash size = 128
Nov  7 20:23:09 beaglebone kernel: [    0.322403] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
Nov  7 20:23:09 beaglebone kernel: [    0.322493] NetLabel:  unlabeled traffic allowed by default
Nov  7 20:23:09 beaglebone kernel: [    0.323619] clocksource: Switched to clocksource timer1
Nov  7 20:23:09 beaglebone kernel: [    0.486397] VFS: Disk quotas dquot_6.6.0
Nov  7 20:23:09 beaglebone kernel: [    0.486501] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.487372] AppArmor: AppArmor Filesystem Enabled
Nov  7 20:23:09 beaglebone kernel: [    0.500590] NET: Registered protocol family 2
Nov  7 20:23:09 beaglebone kernel: [    0.501613] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.501650] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.501692] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.501751] TCP: Hash tables configured (established 4096 bind 4096)
Nov  7 20:23:09 beaglebone kernel: [    0.501897] UDP hash table entries: 256 (order: 1, 8192 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.501919] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
Nov  7 20:23:09 beaglebone kernel: [    0.502268] NET: Registered protocol family 1
Nov  7 20:23:09 beaglebone kernel: [    0.515445] RPC: Registered named UNIX socket transport module.
Nov  7 20:23:09 beaglebone kernel: [    0.515455] RPC: Registered udp transport module.
Nov  7 20:23:09 beaglebone kernel: [    0.515460] RPC: Registered tcp transport module.
Nov  7 20:23:09 beaglebone kernel: [    0.515465] RPC: Registered tcp NFSv4.1 backchannel transport module.
Nov  7 20:23:09 beaglebone kernel: [    0.516436] Unpacking initramfs...
Nov  7 20:23:09 beaglebone kernel: [    0.910750] Freeing initrd memory: 6884K
Nov  7 20:23:09 beaglebone kernel: [    0.911765] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
Nov  7 20:23:09 beaglebone kernel: [    0.915021] Initialise system trusted keyrings
Nov  7 20:23:09 beaglebone kernel: [    0.915433] workingset: timestamp_bits=14 max_order=17 bucket_order=3
Nov  7 20:23:09 beaglebone kernel: [    0.922718] zbud: loaded
Nov  7 20:23:09 beaglebone kernel: [    0.930186] NFS: Registering the id_resolver key type
Nov  7 20:23:09 beaglebone kernel: [    0.930245] Key type id_resolver registered
Nov  7 20:23:09 beaglebone kernel: [    0.930252] Key type id_legacy registered
Nov  7 20:23:09 beaglebone kernel: [    0.930268] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Nov  7 20:23:09 beaglebone kernel: [    0.930623] fuse init (API version 7.27)
Nov  7 20:23:09 beaglebone kernel: [    0.941226] Key type asymmetric registered
Nov  7 20:23:09 beaglebone kernel: [    0.941239] Asymmetric key parser 'x509' registered
Nov  7 20:23:09 beaglebone kernel: [    0.941353] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
Nov  7 20:23:09 beaglebone kernel: [    0.945719] io scheduler noop registered
Nov  7 20:23:09 beaglebone kernel: [    0.945729] io scheduler deadline registered
Nov  7 20:23:09 beaglebone kernel: [    0.946021] io scheduler cfq registered (default)
Nov  7 20:23:09 beaglebone kernel: [    0.946031] io scheduler mq-deadline registered
Nov  7 20:23:09 beaglebone kernel: [    0.950145] pinctrl-single 44e10800.pinmux: 142 pins, size 568
Nov  7 20:23:09 beaglebone kernel: [    0.963542] gpio-of-helper ocp:cape-universal: ready
Nov  7 20:23:09 beaglebone kernel: [    0.977513] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
Nov  7 20:23:09 beaglebone kernel: [    0.981253] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    0.991380] console [ttyS0] enabled
Nov  7 20:23:09 beaglebone kernel: [    0.992613] 48022000.serial: ttyS1 at MMIO 0x48022000 (irq = 31, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    0.993592] 48024000.serial: ttyS2 at MMIO 0x48024000 (irq = 32, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    0.994513] 481a6000.serial: ttyS3 at MMIO 0x481a6000 (irq = 33, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    0.995447] 481a8000.serial: ttyS4 at MMIO 0x481a8000 (irq = 34, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    0.996617] 481aa000.serial: ttyS5 at MMIO 0x481aa000 (irq = 35, base_baud = 3000000) is a 8250
Nov  7 20:23:09 beaglebone kernel: [    1.000491] omap_rng 48310000.rng: Random Number Generator ver. 20
Nov  7 20:23:09 beaglebone kernel: [    1.001618] sdhci: Secure Digital Host Controller Interface driver
Nov  7 20:23:09 beaglebone kernel: [    1.001626] sdhci: Copyright(c) Pierre Ossman
Nov  7 20:23:09 beaglebone kernel: [    1.002137] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22)
Nov  7 20:23:09 beaglebone kernel: [    1.002148] omap_hsmmc 48060000.mmc: Got CD GPIO
Nov  7 20:23:09 beaglebone kernel: [    1.002729] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1
Nov  7 20:23:09 beaglebone kernel: [    1.003074] random: fast init done
Nov  7 20:23:09 beaglebone kernel: [    1.003442] random: crng init done
Nov  7 20:23:09 beaglebone kernel: [    1.029788] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1
Nov  7 20:23:09 beaglebone kernel: [    1.056084] sdhci-pltfm: SDHCI platform and OF driver helper
Nov  7 20:23:09 beaglebone kernel: [    1.088549] at24 2-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
Nov  7 20:23:09 beaglebone kernel: [    1.103807] mmc1: new high speed MMC card at address 0001
Nov  7 20:23:09 beaglebone kernel: [    1.109361] mmcblk1: mmc1:0001 Q2J54A 3.64 GiB 
Nov  7 20:23:09 beaglebone kernel: [    1.110050] mmcblk1boot0: mmc1:0001 Q2J54A partition 1 2.00 MiB
Nov  7 20:23:09 beaglebone kernel: [    1.110675] mmcblk1boot1: mmc1:0001 Q2J54A partition 2 2.00 MiB
Nov  7 20:23:09 beaglebone kernel: [    1.111180] mmcblk1rpmb: mmc1:0001 Q2J54A partition 3 512 KiB, chardev (245:0)
Nov  7 20:23:09 beaglebone kernel: [    1.117286]  mmcblk1: p1
Nov  7 20:23:09 beaglebone kernel: [    1.174417] eqep 48300180.eqep: ver. 1.0
Nov  7 20:23:09 beaglebone kernel: [    1.174650] eqep 48300180.eqep: count_mode:0
Nov  7 20:23:09 beaglebone kernel: [    1.174660] eqep 48300180.eqep: invert_qa:1
Nov  7 20:23:09 beaglebone kernel: [    1.174668] eqep 48300180.eqep: invert_qb:1
Nov  7 20:23:09 beaglebone kernel: [    1.174676] eqep 48300180.eqep: invert_qi:0
Nov  7 20:23:09 beaglebone kernel: [    1.174684] eqep 48300180.eqep: invert_qs:0
Nov  7 20:23:09 beaglebone kernel: [    1.174693] eqep 48300180.eqep: swap_inputs:0
Nov  7 20:23:09 beaglebone kernel: [    1.174702] eqep 48300180.eqep: QDECCTL:0x0180
Nov  7 20:23:09 beaglebone kernel: [    1.174710] eqep 48300180.eqep: QPOSINIT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.174717] eqep 48300180.eqep: QPOSMAX:0xffffffff
Nov  7 20:23:09 beaglebone kernel: [    1.174725] eqep 48300180.eqep: QPOSCNT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.174732] eqep 48300180.eqep: omit_interrupt:0
Nov  7 20:23:09 beaglebone kernel: [    1.174740] eqep 48300180.eqep: QEINT:0x0800
Nov  7 20:23:09 beaglebone kernel: [    1.174747] eqep 48300180.eqep: QUPRD:0x05f5e100
Nov  7 20:23:09 beaglebone kernel: [    1.174754] eqep 48300180.eqep: QEPCTL:0x009e write
Nov  7 20:23:09 beaglebone kernel: [    1.174761] eqep 48300180.eqep: QEPCTL:0x009e read
Nov  7 20:23:09 beaglebone kernel: [    1.174783] eqep 48300180.eqep: irq:135, clk_rate:100000000
Nov  7 20:23:09 beaglebone kernel: [    1.174981] eqep 48302180.eqep: ver. 1.0
Nov  7 20:23:09 beaglebone kernel: [    1.175139] eqep 48302180.eqep: count_mode:0
Nov  7 20:23:09 beaglebone kernel: [    1.175149] eqep 48302180.eqep: invert_qa:1
Nov  7 20:23:09 beaglebone kernel: [    1.175157] eqep 48302180.eqep: invert_qb:1
Nov  7 20:23:09 beaglebone kernel: [    1.175165] eqep 48302180.eqep: invert_qi:0
Nov  7 20:23:09 beaglebone kernel: [    1.175172] eqep 48302180.eqep: invert_qs:0
Nov  7 20:23:09 beaglebone kernel: [    1.175180] eqep 48302180.eqep: swap_inputs:0
Nov  7 20:23:09 beaglebone kernel: [    1.175188] eqep 48302180.eqep: QDECCTL:0x0180
Nov  7 20:23:09 beaglebone kernel: [    1.175196] eqep 48302180.eqep: QPOSINIT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.175203] eqep 48302180.eqep: QPOSMAX:0xffffffff
Nov  7 20:23:09 beaglebone kernel: [    1.175210] eqep 48302180.eqep: QPOSCNT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.175218] eqep 48302180.eqep: omit_interrupt:0
Nov  7 20:23:09 beaglebone kernel: [    1.175224] eqep 48302180.eqep: QEINT:0x0800
Nov  7 20:23:09 beaglebone kernel: [    1.175231] eqep 48302180.eqep: QUPRD:0x05f5e100
Nov  7 20:23:09 beaglebone kernel: [    1.175238] eqep 48302180.eqep: QEPCTL:0x009e write
Nov  7 20:23:09 beaglebone kernel: [    1.175245] eqep 48302180.eqep: QEPCTL:0x009e read
Nov  7 20:23:09 beaglebone kernel: [    1.175264] eqep 48302180.eqep: irq:137, clk_rate:100000000
Nov  7 20:23:09 beaglebone kernel: [    1.175416] eqep 48304180.eqep: ver. 1.0
Nov  7 20:23:09 beaglebone kernel: [    1.175536] eqep 48304180.eqep: count_mode:0
Nov  7 20:23:09 beaglebone kernel: [    1.175547] eqep 48304180.eqep: invert_qa:1
Nov  7 20:23:09 beaglebone kernel: [    1.175555] eqep 48304180.eqep: invert_qb:1
Nov  7 20:23:09 beaglebone kernel: [    1.175563] eqep 48304180.eqep: invert_qi:0
Nov  7 20:23:09 beaglebone kernel: [    1.175570] eqep 48304180.eqep: invert_qs:0
Nov  7 20:23:09 beaglebone kernel: [    1.175578] eqep 48304180.eqep: swap_inputs:0
Nov  7 20:23:09 beaglebone kernel: [    1.175696] eqep 48304180.eqep: QDECCTL:0x0180
Nov  7 20:23:09 beaglebone kernel: [    1.175706] eqep 48304180.eqep: QPOSINIT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.175714] eqep 48304180.eqep: QPOSMAX:0xffffffff
Nov  7 20:23:09 beaglebone kernel: [    1.175720] eqep 48304180.eqep: QPOSCNT:0x00000000
Nov  7 20:23:09 beaglebone kernel: [    1.175728] eqep 48304180.eqep: omit_interrupt:0
Nov  7 20:23:09 beaglebone kernel: [    1.175735] eqep 48304180.eqep: QEINT:0x0800
Nov  7 20:23:09 beaglebone kernel: [    1.175742] eqep 48304180.eqep: QUPRD:0x05f5e100
Nov  7 20:23:09 beaglebone kernel: [    1.175749] eqep 48304180.eqep: QEPCTL:0x009e write
Nov  7 20:23:09 beaglebone kernel: [    1.175755] eqep 48304180.eqep: QEPCTL:0x009e read
Nov  7 20:23:09 beaglebone kernel: [    1.175776] eqep 48304180.eqep: irq:139, clk_rate:100000000
Nov  7 20:23:09 beaglebone kernel: [    1.218944] bone-pinmux-helper: probe of ocp:P8_07_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.260598] bone-pinmux-helper: probe of ocp:P8_08_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.302155] bone-pinmux-helper: probe of ocp:P8_09_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.343718] bone-pinmux-helper: probe of ocp:P8_10_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.385348] bone-pinmux-helper: probe of ocp:P8_11_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.426993] bone-pinmux-helper: probe of ocp:P8_12_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.468295] bone-pinmux-helper: probe of ocp:P8_13_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.509965] bone-pinmux-helper: probe of ocp:P8_14_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.551822] bone-pinmux-helper: probe of ocp:P8_15_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.593632] bone-pinmux-helper: probe of ocp:P8_16_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.635393] bone-pinmux-helper: probe of ocp:P8_17_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.677115] bone-pinmux-helper: probe of ocp:P8_18_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.718568] bone-pinmux-helper: probe of ocp:P8_19_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.760295] bone-pinmux-helper: probe of ocp:P8_26_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.828038] bone-pinmux-helper: probe of ocp:P9_11_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.870710] bone-pinmux-helper: probe of ocp:P9_12_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.913500] bone-pinmux-helper: probe of ocp:P9_13_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.956182] bone-pinmux-helper: probe of ocp:P9_14_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    1.998880] bone-pinmux-helper: probe of ocp:P9_15_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    2.053889] bone-pinmux-helper: probe of ocp:P9_23_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    2.098147] bone-pinmux-helper: probe of ocp:P9_24_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    2.145162] bone-pinmux-helper: probe of ocp:P9_26_pinmux failed with error -22
Nov  7 20:23:09 beaglebone kernel: [    2.185184] libphy: Fixed MDIO Bus: probed
Nov  7 20:23:09 beaglebone kernel: [    2.186145] CAN device driver interface
Nov  7 20:23:09 beaglebone kernel: [    2.187839] c_can_platform 481cc000.can: c_can_platform device registered (regs=5636886d, irq=42)
Nov  7 20:23:09 beaglebone kernel: [    2.189020] c_can_platform 481d0000.can: c_can_platform device registered (regs=f60d3171, irq=43)
Nov  7 20:23:09 beaglebone kernel: [    2.243755] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000
Nov  7 20:23:09 beaglebone kernel: [    2.243771] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
Nov  7 20:23:09 beaglebone kernel: [    2.244736] MDIO: davinci_mdio: dt: updated phy_id[0] from phy_mask[fffffffe]
Nov  7 20:23:09 beaglebone kernel: [    2.263123] libphy: 4a101000.mdio: probed
Nov  7 20:23:09 beaglebone kernel: [    2.263154] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
Nov  7 20:23:09 beaglebone kernel: [    2.264627] cpsw 4a100000.ethernet: Detected MACID = 98:84:e3:92:e5:77
Nov  7 20:23:09 beaglebone kernel: [    2.264792] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
Nov  7 20:23:09 beaglebone kernel: [    2.264804] cpsw 4a100000.ethernet: ALE Table size 1024
Nov  7 20:23:09 beaglebone kernel: [    2.264847] cpsw 4a100000.ethernet: cpts: overflow check period 1250 (jiffies)
Nov  7 20:23:09 beaglebone kernel: [    2.267105] usbcore: registered new interface driver smsc95xx
Nov  7 20:23:09 beaglebone kernel: [    2.269471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Nov  7 20:23:09 beaglebone kernel: [    2.269539] ehci-platform: EHCI generic platform driver
Nov  7 20:23:09 beaglebone kernel: [    2.269964] ehci-omap: OMAP-EHCI Host Controller driver
Nov  7 20:23:09 beaglebone kernel: [    2.271043] usbcore: registered new interface driver usb-storage
Nov  7 20:23:09 beaglebone kernel: [    2.274809] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator
Nov  7 20:23:09 beaglebone kernel: [    2.274971] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0
Nov  7 20:23:09 beaglebone kernel: [    2.278627] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator
Nov  7 20:23:09 beaglebone kernel: [    2.278817] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0
Nov  7 20:23:09 beaglebone kernel: [    2.282410] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
Nov  7 20:23:09 beaglebone kernel: [    2.282451] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
Nov  7 20:23:09 beaglebone kernel: [    2.282816] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
Nov  7 20:23:09 beaglebone kernel: [    2.282826] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Nov  7 20:23:09 beaglebone kernel: [    2.282833] usb usb1: Product: MUSB HDRC host driver
Nov  7 20:23:09 beaglebone kernel: [    2.282841] usb usb1: Manufacturer: Linux 4.19.94-ti-r42 musb-hcd
Nov  7 20:23:09 beaglebone kernel: [    2.282848] usb usb1: SerialNumber: musb-hdrc.1
Nov  7 20:23:09 beaglebone kernel: [    2.283846] hub 1-0:1.0: USB hub found
Nov  7 20:23:09 beaglebone kernel: [    2.283946] hub 1-0:1.0: 1 port detected
Nov  7 20:23:09 beaglebone kernel: [    2.295882] omap_rtc 44e3e000.rtc: already running
Nov  7 20:23:09 beaglebone kernel: [    2.296622] omap_rtc 44e3e000.rtc: registered as rtc0
Nov  7 20:23:09 beaglebone kernel: [    2.298384] i2c /dev entries driver
Nov  7 20:23:09 beaglebone kernel: [    2.302880] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
Nov  7 20:23:09 beaglebone kernel: [    2.303558] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
Nov  7 20:23:09 beaglebone kernel: [    2.308377] ledtrig-cpu: registered to indicate activity on CPUs
Nov  7 20:23:09 beaglebone kernel: [    2.308962] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
Nov  7 20:23:09 beaglebone kernel: [    2.309310] omap-aes 53500000.aes: will run requests pump with realtime priority
Nov  7 20:23:09 beaglebone kernel: [    2.312359] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
Nov  7 20:23:09 beaglebone kernel: [    2.316650] hidraw: raw HID events driver (C) Jiri Kosina
Nov  7 20:23:09 beaglebone kernel: [    2.324824] gnss: GNSS driver registered with major 242
Nov  7 20:23:09 beaglebone kernel: [    2.332483] NET: Registered protocol family 10
Nov  7 20:23:09 beaglebone kernel: [    2.402988] Segment Routing with IPv6
Nov  7 20:23:09 beaglebone kernel: [    2.403145] mip6: Mobile IPv6
Nov  7 20:23:09 beaglebone kernel: [    2.403303] NET: Registered protocol family 17
Nov  7 20:23:09 beaglebone kernel: [    2.403334] can: controller area network core (rev 20170425 abi 9)
Nov  7 20:23:09 beaglebone kernel: [    2.403432] NET: Registered protocol family 29
Nov  7 20:23:09 beaglebone kernel: [    2.403528] 8021q: 802.1Q VLAN Support v1.8
Nov  7 20:23:09 beaglebone kernel: [    2.403774] Key type dns_resolver registered
Nov  7 20:23:09 beaglebone kernel: [    2.403783] mpls_gso: MPLS GSO support
Nov  7 20:23:09 beaglebone kernel: [    2.404138] ThumbEE CPU extension supported.
Nov  7 20:23:09 beaglebone kernel: [    2.404156] Registering SWP/SWPB emulation handler
Nov  7 20:23:09 beaglebone kernel: [    2.412509] registered taskstats version 1
Nov  7 20:23:09 beaglebone kernel: [    2.412520] Loading compiled-in X.509 certificates
Nov  7 20:23:09 beaglebone kernel: [    2.412649] zswap: loaded using pool lzo/zbud
Nov  7 20:23:09 beaglebone kernel: [    2.415968] Btrfs loaded, crc32c=crc32c-generic
Nov  7 20:23:09 beaglebone kernel: [    2.416079] AppArmor: AppArmor sha1 policy hashing enabled
Nov  7 20:23:09 beaglebone kernel: [    2.473346] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set
Nov  7 20:23:09 beaglebone kernel: [    2.474152] input: tps65217_pwr_but as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0
Nov  7 20:23:09 beaglebone kernel: [    2.475135] tps65217 0-0024: TPS65217 ID 0xe version 1.2
Nov  7 20:23:09 beaglebone kernel: [    2.476201] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
Nov  7 20:23:09 beaglebone kernel: [    2.476312] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
Nov  7 20:23:09 beaglebone kernel: [    2.480954] cpu cpu0: Linked as a consumer to regulator.3
Nov  7 20:23:09 beaglebone kernel: [    2.481063] cpu cpu0: Dropping the link to regulator.3
Nov  7 20:23:09 beaglebone kernel: [    2.481563] cpu cpu0: Linked as a consumer to regulator.3
Nov  7 20:23:09 beaglebone kernel: [    2.483956] omap_rtc 44e3e000.rtc: setting system clock to 2023-11-07 20:22:56 UTC (1699388576)
Nov  7 20:23:09 beaglebone kernel: [    2.485464] ALSA device list:
Nov  7 20:23:09 beaglebone kernel: [    2.485472]   No soundcards found.
Nov  7 20:23:09 beaglebone kernel: [    2.491875] Freeing unused kernel memory: 1024K
Nov  7 20:23:09 beaglebone kernel: [    2.492601] Run /init as init process
Nov  7 20:23:09 beaglebone kernel: [    7.514291] EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
Nov  7 20:23:09 beaglebone kernel: [   10.475940] EXT4-fs (mmcblk1p1): re-mounted. Opts: errors=remount-ro
Nov  7 20:23:12 beaglebone kernel: [   18.038074] net eth0: initializing cpsw version 1.12 (0)
Nov  7 20:23:12 beaglebone kernel: [   18.117195] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL)
Nov  7 20:23:12 beaglebone kernel: [   18.141442] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Nov  7 20:23:12 beaglebone kernel: [   18.141463] 8021q: adding VLAN 0 to HW filter on device eth0
Nov  7 20:23:13 beaglebone kiwid: 00:00:00.826   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:23:13 beaglebone kiwid: 00:00:00.834   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:23:13 beaglebone kiwid: 00:00:00.834   /etc/debian_version 10.11
Nov  7 20:23:13 beaglebone kiwid: 00:00:00.845   background mode: delaying start 30 secs...
Nov  7 20:23:14 beaglebone kernel: [   20.168851] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
Nov  7 20:23:14 beaglebone kernel: [   20.168943] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Nov  7 20:23:14 beaglebone kernel: [   20.814809] using random self ethernet address
Nov  7 20:23:14 beaglebone kernel: [   20.814827] using random host ethernet address
Nov  7 20:23:15 beaglebone kernel: [   21.100938] Mass Storage Function, version: 2009/09/11
Nov  7 20:23:15 beaglebone kernel: [   21.100962] LUN: removable file: (no medium)
Nov  7 20:23:15 beaglebone kernel: [   21.418918] using random self ethernet address
Nov  7 20:23:15 beaglebone kernel: [   21.418938] using random host ethernet address
Nov  7 20:23:15 beaglebone kernel: [   21.626914] usb0: HOST MAC 98:84:e3:92:e5:7a
Nov  7 20:23:15 beaglebone kernel: [   21.629878] usb0: MAC 98:84:e3:92:e5:79
Nov  7 20:23:15 beaglebone kernel: [   21.644061] usb1: HOST MAC 98:84:e3:92:e5:7c
Nov  7 20:23:15 beaglebone kernel: [   21.644376] usb1: MAC 98:84:e3:92:e5:7d
Nov  7 20:23:15 beaglebone kernel: [   21.896892] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
Nov  7 20:23:16 beaglebone kernel: [   22.068995] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready
Nov  7 20:23:26 beaglebone kernel: [   33.751561] remoteproc remoteproc0: wkup_m3 is available
Nov  7 20:23:26 beaglebone kernel: [   33.807862] remoteproc remoteproc0: powering up wkup_m3
Nov  7 20:23:26 beaglebone kernel: [   33.807894] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 217168
Nov  7 20:23:26 beaglebone kernel: [   33.808179] remoteproc remoteproc0: remote processor wkup_m3 is now up
Nov  7 20:23:26 beaglebone kernel: [   33.808206] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x193
Nov  7 20:23:26 beaglebone kernel: [   33.912909] PM: bootloader does not support rtc-only!
Nov  7 20:23:28 beaglebone kernel: [   35.151124] remoteproc remoteproc1: 4a334000.pru is available
Nov  7 20:23:28 beaglebone kernel: [   35.151309] pru-rproc 4a334000.pru: PRU rproc node pru@4a334000 probed successfully
Nov  7 20:23:28 beaglebone kernel: [   35.163926] remoteproc remoteproc2: 4a338000.pru is available
Nov  7 20:23:28 beaglebone kernel: [   35.164132] pru-rproc 4a338000.pru: PRU rproc node pru@4a338000 probed successfully
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.184   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.190   reading configuration from file /root/kiwi.config/admin.json: 119 tokens (1.4k bytes)
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.579   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.582   serial number from EEPROM: 1697
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.584   model: KiwiSDR 1
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.586   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.589   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.613   DX: 872 label entries
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.615   DX: file = 872,db6868b3,52120
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.618   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.622   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.645   DX: 874 label entries
Nov  7 20:23:43 beaglebone kiwid: 00:00:31.648   DX: file = 874,e53425f4,52531
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.257 ....      firmware: SDR_RX4_WF4
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.261 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.262 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.262 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.262 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.262 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.268 ....      webserver: OK, port [::]:8073
Nov  7 20:23:45 beaglebone kiwid: 00:00:33.502 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:23:46 beaglebone kiwid: 00:00:34.370 ....      FPGA not responding: 0xffff
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.086   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.091   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.092   /etc/debian_version 10.11
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.229   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.232   reading configuration from file /root/kiwi.config/admin.json: 121 tokens (1.5k bytes)
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.620   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.623   serial number from EEPROM: 1697
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.625   model: KiwiSDR 1
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.627   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.630   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.651   DX: 872 label entries
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.653   DX: file = 872,db6868b3,52120
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.656   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.659   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.679   DX: 874 label entries
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.681   DX: file = 874,e53425f4,52531
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.684 ....      firmware: SDR_RX4_WF4
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.686 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.688 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.688 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.688 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.688 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.694 ....      webserver: OK, port [::]:8073
Nov  7 20:23:58 beaglebone kiwid: 00:00:00.925 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:23:59 beaglebone kiwid: 00:00:01.781 ....      FPGA not responding: 0xffff
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.336   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.341   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.342   /etc/debian_version 10.11
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.479   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.482   reading configuration from file /root/kiwi.config/admin.json: 121 tokens (1.5k bytes)
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.870   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.873   serial number from EEPROM: 1697
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.875   model: KiwiSDR 1
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.877   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.877   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.900   DX: 872 label entries
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.902   DX: file = 872,db6868b3,52120
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.905   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.908   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.928   DX: 874 label entries
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.931   DX: file = 874,e53425f4,52531
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.933 ....      firmware: SDR_RX4_WF4
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.935 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.935 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.935 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.939 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.939 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:24:11 beaglebone kiwid: 00:00:00.943 ....      webserver: OK, port [::]:8073
Nov  7 20:24:12 beaglebone kiwid: 00:00:01.176 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:24:12 beaglebone kiwid: 00:00:02.034 ....      FPGA not responding: 0xffff
Nov  7 20:24:24 beaglebone kiwid: 00:00:00.585   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:24:24 beaglebone kiwid: 00:00:00.590   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:24:24 beaglebone kiwid: 00:00:00.590   /etc/debian_version 10.11
Nov  7 20:24:24 beaglebone kiwid: 00:00:00.727   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:24:24 beaglebone kiwid: 00:00:00.730   reading configuration from file /root/kiwi.config/admin.json: 121 tokens (1.5k bytes)
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.119   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.121   serial number from EEPROM: 1697
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.123   model: KiwiSDR 1
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.126   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.126   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.149   DX: 872 label entries
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.151   DX: file = 872,db6868b3,52120
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.154   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.157   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.177   DX: 874 label entries
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.179   DX: file = 874,e53425f4,52531
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.182 ....      firmware: SDR_RX4_WF4
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.184 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.186 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.186 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.186 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.187 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.192 ....      webserver: OK, port [::]:8073
Nov  7 20:24:25 beaglebone kiwid: 00:00:01.423 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:24:26 beaglebone kiwid: 00:00:02.279 ....      FPGA not responding: 0xffff
Nov  7 20:24:37 beaglebone kiwid: 00:00:00.836   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:24:37 beaglebone kiwid: 00:00:00.842   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:24:37 beaglebone kiwid: 00:00:00.842   /etc/debian_version 10.11
Nov  7 20:24:37 beaglebone kiwid: 00:00:00.979   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:24:37 beaglebone kiwid: 00:00:00.982   reading configuration from file /root/kiwi.config/admin.json: 121 tokens (1.5k bytes)
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.370   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.373   serial number from EEPROM: 1697
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.375   model: KiwiSDR 1
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.377   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.378   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.401   DX: 872 label entries
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.403   DX: file = 872,db6868b3,52120
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.406   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.409   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.429   DX: 874 label entries
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.432   DX: file = 874,e53425f4,52531
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.434 ....      firmware: SDR_RX4_WF4
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.436 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.438 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.438 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.438 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.439 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.444 ....      webserver: OK, port [::]:8073
Nov  7 20:24:38 beaglebone kiwid: 00:00:01.675 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:24:39 beaglebone kiwid: 00:00:02.528 ....      FPGA not responding: 0xffff
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.086   KiwiSDR v1.633 --------------------------------------------------------------------
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.091   compiled: Nov  7 2023 19:34:59 on kiwisdr
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.091   /etc/debian_version 10.11
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.229   reading configuration from file /root/kiwi.config/kiwi.json: 363 tokens (4.9k bytes)
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.232   reading configuration from file /root/kiwi.config/admin.json: 121 tokens (1.5k bytes)
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.620   EEPROM check: old format serial_no compatibility 11697 => 1697
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.623   serial number from EEPROM: 1697
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.625   model: KiwiSDR 1
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.627   reading configuration from file /root/kiwi.config/dx_config.json
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.627   reading configuration from file /root/kiwi.config/dx.json
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.650   DX: 872 label entries
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.652   DX: file = 872,db6868b3,52120
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.655   reading configuration from file /root/kiwi.config/dx_community_config.json
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.657   reading configuration from file /root/kiwi.config/dx_community.json
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.678   DX: 874 label entries
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.680   DX: file = 874,e53425f4,52531
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.683 ....      firmware: SDR_RX4_WF4
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.685 ....      firmware: rx_chans=4 wf_chans=4 gps_chans=12
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.686 ....      firmware: RX rx_decim=5555 RX1_STD_DECIM=505 RX2_STD_DECIM=11 USE_RX_CICF=0
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.687 ....      firmware: RX srate=12001.062(12000) bufs=4 samps=170 loop=85 rem=0 intr_usec=14166
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.687 ....      firmware: WF xfer=9 samps=911 rpt=50 loop=18 rem=11
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.687 ....      webserver: listening on port 8073/8073 for HTTP connections
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.692 ....      webserver: OK, port [::]:8073
Nov  7 20:24:51 beaglebone kiwid: 00:00:00.923 ....      ### open SPI_DEV /dev/spidev0.0
Nov  7 20:24:52 beaglebone kiwid: 00:00:01.778 ....      FPGA not responding: 0xffff

... and so on, looping error, same after reboot, powercycling, reattaching the hat, etc. ...