The KiwiSDR 2 online store is open for orders! Please visit kiwisdr.nz
f6bir
About
- Username
- f6bir
- Joined
- Visits
- 205
- Last Active
- Roles
- Member
- Points
- 1
Comments
-
Thank you for your suggestion, I think I will go back to the config from the beginning, all the setups I have tried have been found to be unstable, I will also try a dedicated router solution with a Raspberry for my two kiwis. Currently I am running…
-
Good evening , how to make permanent the parameters entered in resolv.conf which changes with each reboot of the kiwi 73 'Rene F6BIR
-
what follows: "eureka " Mon Aug 31 12:03:42 03:47:24.742 0... TIMEZONE: timezonedb.com curl error Mon Aug 31 12:04:42 03:48:24.750 0... TIMEZONE: lat/lon from admin public config: (49.224380, 2.210537) Mon Aug 31 12:04:43 03:48:…
-
Ury, good news this works with adding "nameserver 8.8.8.8 in resolv.conf, how to make it permanent without using connman." Thank you for your patience
-
Hello all, not resolved yet message in log: Mon Aug 31 07:59:57 21:50:45.537 0... [01] PWD admin config pwd set TRUE, auto-login FALSE Mon Aug 31 08:00:28 21:51:17.020 0... TIMEZONE: lat/lon from admin public config: (49.224380, 2.210537) Mon …
-
Yes Yuri it does something and also with ping 50.116.2.70 but not with kiwisdr.com (may be normal on BBB) All seems ok now the UTC time is correct I am testing WSPR for a while to check if UTC time is updated normaly. Local time is always faulty ind…
-
Below the both kiwi only wifi wlan0 connected but interner access always fault TU (Image)
-
Hi Yuri I had the tow interfaces connected to modify the set up I send it just to verify the interfaces files data Tu 73 Rene
-
hello there was an error in the word "gateway", do you think this is correct now, but still no positive result thank you (Image)
-
I modified the network config, (wpa_supplicant.conf and interfaces) now the two kiwis are identical, the problem is not solved for all that tomorrow I will use connman to redo a new config Thank you for your help(Image)
-
Yes see belowing For the first one root@192.168.1.27's password: Last login: Thu Aug 27 05:15:34 2020 from 192.168.1.86 root@kiwisdr:~# ifconfig eth0 Link encap:Ethernet HWaddr 78:04:73:83:2a:c0 UP BROADCAST MULTICAST DYNAMIC …
-
Hello and thank you for your suggestions. Concerning the box and the router, I have already checked or even modified certain parameters without success. I realized the manip proposed by JKS here are the results for the two kiwis and on a Raspi (and …
-
hi, good question but where can I check this, I also noticed that I disappeared from the kiwi map when I was only in wifi this would explain that Thank you for your relevance 73 'F6bir Rene
-
Thank you Yury for your help, I tested your suggestion, it doesn't answer anything if I'm only on wifi and it works if I reconnect the Ethernet cable root@kiwisdr:~/Beagle_SDR_GPS# curl -s --ipv4 "https://api.timezonedb.com/v2.1/get-time-zone?…
-
Hello, Yes i added wifi USB dongle to BBG and Kiwi run with it (camanserville.no-ip.biz:8074) without wired connection. I have 2 kiwi and i have the same problem on both, if I put the wired connection all the local time will be ok (camanserville.no-…
-
Hi Yuri, Thanks for replay, the utc time is correct by GPS only the local time is missing, if I connect the ethernet wired link everything becomes ok again (Image) 73' Rene
-
In fact the frequency sent by kiwirecorder to the remote KIWI is correct but KIWISDR adds the offset value to the frequency the recording does not correspond to the request and the decoding does not succeed(Image) RX0: local wspr aurtorun RX1: I …
-
All is OK now TU
-
Hello What is the new KiwiSdr link, rx.kiwisdr.com above don't run TU Rene
-
Hi Rob I am happy to read this, do you know other one using RTL_SDR on 2 meters, I am runing V2.5a on PI-B+ (old cb) I was not able to install V2.7 on it (mkdir wspr-captures problem !) TU
-
Hello does anyone experience using RTL_SDR in VHF (144.489) and know the values ??to set in the noise_ca_vals.csv file. the antenna is a 6 elements quad Rene F6BIR
-
errato: it is for a downconverter of course
-
Hello Thank you for answer, the need was only for a local administrator use, to use it like a hard multi-band receiver without web connection , I understood it is a problem for public access connection, that was just an idea Thank a lot. 73' F6BIR
-
Hello Can we imagine switching from HF mode to converter mode simply by changing the antenna 73' Ren? f6bir
-
Ok thank you 73 Ren?
-
Hello all, How to access to the extension WSPR when the kiwi is declared with a down converter, the option 2m is not available on the drop-down list, but it seems to me that at the beginning this option was visible thank you
-
Hello John, Oui j'ai bien compris le niveau de difficult? ? r?aliser cette id?e, merci pour la r?ponse Cordialement Ren? F6bir
-
thank you all well understood
-
Hello JKS, Thank you for answer, in the log ml ms mu do not appear the WSPR decoded stations as in the admin current log. I can see them on WSPRNET web site, but I would like start an autorun wspr without web connection for a while and to have a …
-
Hi Martin Thank you for answer, my idea was to do that with a short-cut to view immediately the SNR difference between antennas like using WSPR or FT8 mode. (antennas are loop, dipoles, GP R7 and miniwip, on 20m miniwip seams better ) Actually I u…