jimjackii
About
- Username
- jimjackii
- Joined
- Visits
- 277
- Last Active
- Roles
- Member
- Points
- 3
Comments
-
Hi John, Thanks. Unfortunately, I hadn't noticed the overlapping areas. Then of course it makes sense to use the prioritized area as a basis. Regards, Steffen
-
I know the settings. They are correct as far as I can tell. The jump from 1 kHz in the 40 m amateur radio band does work. However, only the special case of 7200 kHz back to 7199 kHz results in a jump from -5 kHz to 7195 kHz. From 7199 kHz, it jumps …
-
I don't know if this has anything to do with the ‘+’ problem mentioned. I also use a ‘+’ in the switch URL and have no problems switching even with the new Mongose package. For me, the switchover is handled by an ESP8266 with Tasmota firmware, and t…
-
https://forum.kiwisdr.com/index.php?p=/discussion/comment/21301#Comment_21301 I am only familiar with LoRa data in a horizontal line, not diagonally. I once had a LoRa/LoRaWAN access point running for a while. Regards, Steffen
-
Martin, many thanks for the recommendation.
-
I have a similar amplifier (see link) on my Kiwi 1 with an endfed. But I still have a 16 dB attenuator after the amplifier, because the 30 dB overdrive the Kiwi ADC. The quality is reasonably good - I've had worse amplifiers. https://www.amazon.de/V…
-
I have to ask again. The thread may have been lost a bit. Is the waterfall also automatically adjusted when the aerial is switched? If so, it doesn't work for me. Regards, Steffen
-
I also ordered this kit from LZ1AQ a few weeks ago and now it's here with me, waiting for me to finally build the loops. ;-) Maybe I'll have a few hours over Easter to test the kit. I will also report back. Regards, Steffen
-
I use an RF switch board with HMC849 (important because it goes down to DC) in conjunction with a relay module with ESP8266 (then flashed with the Tasmota firmware). https://www.amazon.de/dp/B08LHBVYFD?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 http…
-
Ok, thank you. Then I'll have to keep an eye on it and check /var/log if it occurs again. Regards, Steffen
-
Ok, thanks John. I have now tested it again with Chrome - it works as you described. After clearing the browser cache, it starts with the configured colormap (here "Kiwi"), otherwise with the colormap set in the browser. Strangely enough, …
-
I can confirm that these powerline adapters are a major source of interference. I also used them to connect to a garden shed. Unfortunately, there was a lot of interference (horizontal lines) on the Kiwi waterfall, which became stronger with more ne…
-
I had such massive problems, which look like your waterfall, with Powerline devices. Since I banned them from my house, things have got much better. Perhaps you or your neighbours also have problems with network switches? Your neighbours' powerline …
-
Now that my antenna switch is working well, I have noticed one more thing that I wanted to ask if this is correct. With 2 users the antenna switch is disabled, that's clear to me so far. If one of the two users disconnects and only one user is still…
-
Thank you for the changes. The cURL commands with "+" work. It also switches to the default antenna, but not when no users are connected, but only when the first user connects to the Kiwi. Would it be possible to hide the "RF attn&quo…
-
The VAR query enters a $AJAX BAD STATUS=404 url=/VER back. I'll have to have a closer look, my knowledge of JavaScript etc. is not too good. Webserver caching is always OFF. Thanks also for the reference to the other forum thread. Regards, Steffen
-
This would be an alternative for people who could configure a private reverse proxy. At this point I have a question - what would be the configuration for an Apache2 reverse proxy? Unfortunately I have not yet managed to configure this on my Apache2…
-
Strange, I tried my lines above to switch the antenna again and it worked once, but not after that. Regards, Steffen
-
Oh, sorry. Then I've made a mistake. The first time I inserted these lines with spaces in between http://192.168.x.y/cm?cmnd=Power2%20Off http://192.168.x.y/cm?cmnd=Power1%20Off it did not work. I had read that spaces are removed and thought that t…
-
I have also no problems with the button "zoom to band". (Kiwi 1, v1.803, Debian 11.9)
-
Thank you for solving the problem. I have understood that. I didn't realise or didn't notice that there were 2 entries with the same name. I hadn't created them directly, they were probably the result of my experimenting. The warning about 2 identic…
-
I have sent you an email with the login details.
-
Thank you for the iframe options. I wanted to customise the Part 7 Solar Condition (solar cond) for me, but there was a problem. The default setting is a window with 175 x 555 with HTML code: <center><a href="//www.hamqsl.com/solar.htm…